Scan View SCANMATE F10 Manual de usuario Pagina 134
- Pagina / 154
- Tabla de contenidos
- MARCADORES
- GE Fanuc Automation 1
- Warnings, Cautions, and Notes 2
- Content of this Manual 3
- Related Publications 4
- Contents 5
- Chapter 1 Introduction 8
- Module Description 9
- Connectors 10
- Required Equipment 11
- Parts of a Remote Drop 12
- Series 90–70 Racks 13
- Series 90–70 Power Supplies 14
- Remote Drop Capacity 16
- Genius Bus 18
- Redundancy 21
- Genius Bus Redundancy 22
- Redundant Bus Configuations 23
- Configuration 25
- Configurable Features 26
- Configuration Protection 27
- Chapter 2 Installation 28
- System Grounding Procedures 29
- Rack Installation 30
- Rack Grounding 31
- Rack Number Selection 31
- Power Supply Installation 33
- Module Locations 34
- Installing a Module 35
- Removing a Module 35
- Field Wiring to I/O Modules 36
- JACKSCREW 37
- WIRE BUNDLE CABLE TIE CLEAT 37
- Terminator Plug 38
- Single Bus Termination 39
- Dual Bus Termination 40
- Bus Stub Connections 41
- Grounding 42
- Connection Instructions 42
- Serial Port Termination 43
- RS–485 RS–232 44
- CONVERTER 44
- Multidrop Connections 45
- GENIUS BUS 46
- SERIAL NETWORK CABLE 46
- 41Chapter 2 Installation 48
- I/O Scan 50
- I/O Scanner Memory 51
- Data Transfer with the Host 52
- Output Defaults 54
- Configuring a Remote Drop 61
- Selecting the Bus Address 62
- Drop IDs and Bus Addresses 63
- Attaching a “Detached” File 64
- Using Auto I/O Map 66
- Bus Scan Time Impact 67
- Genius Interface Entries 68
- SNP Port Entries 69
- Sweep Control Entries 70
- Module Reference Address 71
- Module Characteristics 71
- Return to the Rack Display 72
- Entering Additional Modules 73
- Reference Overlaps 75
- Viewing/Editing the I/O Map 76
- Viewing PLC References 77
- Storing the Configuration 81
- Logicmaster 90 Software 85
- Set Up the Hand–held Monitor 90
- F1:PROG BLOCK ID 91
- F2:CONFIG BLOCK 91
- F3:COPY CONFIG 91
- Select the Device Number 92
- PROG BLOCK ID 93
- I/O ?– ?? 93
- BLOCK NO. ? 93
- Select the Baud Rate 94
- PROG REMOTE MAP 96
- %I ____ 96
- LENGTH(PTS) ____ 96
- Select the Remote Drop ID 97
- Select Genius Bus Redundancy 99
- Select BSM Control 99
- Select CPU Redundancy 100
- CONFIG PROTECT 101
- DISABLED 101
- tgl entr nxt 101
- Remote Drop Data 102
- Forcing Circuits 103
- Toggling I/O Circuits 104
- Overriding I/O Circuits 104
- Genius Hand–held Monitor 105
- Identifying the Circuit 105
- 3 + 33 – 1 = 35 106
- Forcing/Unforcing I/O 107
- Forcing an Analog Circuit 108
- MNTR _ 109
- chng entr 109
- Logicmaster 90–70 110
- Computer 115
- Overview 116
- Displaying Additional Faults 118
- Drop ID#, rack, slot 119
- rack, slot, bus 119
- Fault Clearing 120
- Status References 123
- Datagram Types 126
- Read Map 127
- Read Map Reply 127
- Write Map 127
- Report Fault Datagram Format 128
- Fault Byte 3 129
- Fault Bytes 4 and 5 129
- Fault Bytes 6 and 7 129
- Example 1 132
- Example 2 132
- Input Def : OFF 137
- Out Rnable: YES 137
- Input Default/Out Enable 139
- Step 1: Create a Folder 143
- Scanner 147
- Configuration Limits 149
© 2020, manymanuals.es. Todos los derechos reservados | 0.211 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales